![]() If you'd like to practice this technique, I have used it in my Rilo hat, which is a free knitting pattern. Not only is it extremely practical - it's aesthetically pleasing too! Before you know it, you will have gained a new skill that you can use in any project that needs a stretchy 1x1 trim. The long tail tubular cast on can be a little tricky to get the hang of at first, but I promise that, if you persevere, it will click. Remember to go up a needle size for the rib! Knit the stitch as normal on the second row. On the first row only, you will need to knit into the back of the stitch, as the stitches will be twisted on the needle. Now, work two rows in tubular stocking stitch, knitting the knit stitches and slipping the purl stitches purlwise with yarn in front. Once you're done, tie the two strands under the needle to secure them. Repeat steps 4 and 5 until you have enough stitches. You've cast on a "knit" stitch in your 1x1 rib. Now, bring the needle over and in front of the tail end, and catch the long end from the top and loop over needle, bringing it up from under the tail end. ![]() You've cast on a "purl" stitch in your 1x1 rib. With the needle in your right hand, move the needle over and behind the long end, and catch the tail end from the top and loop over needle, bringing it up from under the long end. Hold both ends in your left hand and separate the threads with your fingers and thumb, with the tail end around your thumb and the long end around your first finger. This counts as a "knit" stitch in your 1x1 rib cast on. Make a slip knot, leaving a very long end (approximately four times the width of the piece you are knitting) and slip it onto your needle. The Long Tail Cast OnĬast on with needles one size smaller than the ones you will be using on the rib Grab some scrap yarn and appropriate needles. I will be demonstrating this cast on with a 1x1 rib trim. I will be sharing the technique via video, as well as written instructions below, so use whichever learning style suits you best. Enjoy! ![]() Perhaps you've been searching for the perfect stretchy cast on or maybe you've been told to use the long tail tubular cast on in a knitting pattern you're using. Either way, today I will be teaching you how to knit this fantastic cast on, which will seriously improve any of your knitting projects that require a bit of stretch. learn to Knit the Long Tail tubular Cast On It is also extremely stretchy, with great recovery ideal for 1x1 rib. This cast on gives a lovely rounded edge to the knitting, much like the edges you get with good quality machine knits. That's where the long tail tubular cast on comes in. The edge is too firm to stretch adequately. It works very well in situations where you need a firm edge, but it is useless when used on something that needs a stretchy ribbing, such as socks or a hat. Little did I know that there are better options available. My Nannan had taught me the cable cast on when I learnt to knit and that's all I used for years. Stretching your thumb and finger apart, whilst holding on to the tail and ball yarns in the rest of your fingers, will help tighten up loose stitches.For the first few years of my knitting life, I had no idea that there were a variety of cast ons to choose from. Take your thumb out of the tail loop, and pull it (not too tight, just so that it sits cleanly under the new stitch on the right needle) Then continue on your way with a normal long tail cast on, bringing your needle towards you, then under the loop on your thumb.Īnd bring it through the tail loop towards you to create a new stitch. Take your finger, and place it over the yarn and the tail end to keep it from moving around. ![]() So take the tail end, fold it in half like so, and place over the needle. Blue for the yarn that comes from the ball, and yellow for the tail end. I start with yellow and blue spitpliced yarn to help you see which bit of yarn does what. I like that’s it’s super fast and stretchy but strong. Experiment to find just the right tension for you. Learn how to start your knitting project with this video and photo tutorial for the long-tail cast on The long tail cast on is my favorite cast on, I used it for pretty much all of my knitting projects unless it’s otherwise specified. Too tight, you’ll lose your nice elastic edge, too loose and it’ll look sloppy. Don’t pull tight on the tail strand, just pull it so that it sits cleanly under the stitches. The doubled tail strand, which sits like scarves around the base of the stitches on the needle, gives a lovely rolled cast on edge, and also helps give a good elasticity to the cast on. Lucy Neatby also refers to this in her knitting videos. I learned this from JC Briar, an absolutely amazing teacher. Knittinghelp has a great video tutorial for it.Ī doubled tail long tail long tail cast on basically takes the tail, doubles it, and continues as normal. You’ll need to be familiar with the long tail cast on, aka double cast on, continental cast on, sling shot, two-strand, Y cast on, german cast on.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |